[edit] Steps

1. Install recording and editing software on your computer. The standard sound recorder application that comes with most PCs will not enable you to record an LP to your hard drive. There are, however, a variety of programs that record audio, ranging from freeware to very expensive professional editing software. Some of these obviously work better than others, and some have more features, but in general you want a program that writes files directly to the hard drive and that enables you to do some minor editing of the recorded files. For a more thorough discussion of recording and editing software, including reviews, visit the external links–Clive Backham's page in particular–listed at the end of this article.
2. Determine whether you need a preamp. You will need to amplify and equalize the sound from your turntable in order to record it onto your computer. If your turntable has a built-in preamp, you should be able to plug it directly into your computer's sound card. If you don't have a built-in preamp, you can either plug the turntable into a stereo receiver and plug the receiver into your computer sound card, or you can purchase a preamp–you can get these at most computer, audio or electronics stores–and plug your turntable into that. Make sure you buy a preamp with "RIAA Equalization" – cheaper ones may not have this, and it is necessary for LPs made after about 1950.
3. Make sure you have the necessary cables and converters to connect the turntable, stereo, or preamp to the sound card. You may need to purchase cables–standard RCA cables, most likely–to connect all the components. Depending on the type of input and output jacks you have on your sound card, turntable, preamp and receiver, you may also need converters to allow you to connect each component to the next. Cables and converters can be purchased at most electronics or audio stores, and if you don't know what you need simply bring in the equipment you have. In the most common case, being you already have a turntable connected to a stereo system, the only additional cable you should need is an inexpensive 3.5mm Stereo to RCA Cable to connect the receiver to the computer, which can alternately be used to play sound from your computer through your stereo system.
4. Connect all the components. If you are not using a preamp you'll need to run a cable from the headphone or "audio out" jack on the turntable or stereo to the input or "line in" jack on your computer's sound card. If you have a preamp, connect the cable from the turntable to the "line in" jack on the preamp and then connect another cable from the "audio out" jack on the preamp to the "line in" jack on the computer sound card.
5. Clean the LP. Obviously a clean record plays a lot better than a dirty one, and if you're making a recording you want the vinyl to sound its best. Your best bet is to use a professional LP-cleaning machine, but these can be expensive and hard to find (you can get similar results, however, if you have a wet-dry vacuum cleaner and some cleaning solution). You can also wash records in the kitchen sink or use specially-designed brushes to clear surface dust. You want to be very careful cleaning your records, and there are more tips and warnings than can be listed here, so check out the external links for more information.
6. Set your recording input level. You can adjust the input level either on the stereo receiver or in the recording software, however "line" outputs on stereos are generally fixed-volume so it's usually best to adjust the recording volume on your computer. You want to make sure that the input is loud enough so that the resulting CD isn't significantly quieter than your other CDs. More importantly, you must ensure that the input volume isn't too loud. If your recording level goes above 0 dB at any point, the sound quality will be distorted, so it's important to stay below this threshold. Try to identify the peak volume (the loudest part) on the LP you wish to record. Some software programs will find the peak for you when you play the record through; otherwise, you'll have to do a little guesswork. Just to be safe, set the input level so that the LP's peak volume records at about -3 dB.
7. Do a test run. Make sure your program is running, and your turntable, and receiver or preamp, are on. Start playing the record and press the "record" button in your audio software. Record only a small bit of audio to see if everything works, then adjust settings in the program and on the player accordingly. You may also want to play the entire LP to make sure there no skips.
8. Record the LP. Press the "record" button in your software before starting the LP. Play the album the whole way through as you transfer the music into electronic format, and stop recording only after the LP has finished playing (you can cut out the silence at the beginning and end of the recording later). Your software program may split tracks for you automatically, but if it does not, don't worry about splitting them now.
9. Edit your recording. If the LP you recorded is in great condition and if your recording equipment is of high quality and is correctly configured, you may not need to do much editing at all. Probably, however, you will at least want to delete any long silences at the beginning and end of the recording, and you should also split the tracks so that you can skip from song to song on your CD. Depending on your editing software, you should also be able to take out or minimize most background noise and imperfections, and normalize the volume. The procedures for such editing vary from program to program, so it's best to consult your software manual or help files.
10. Organize and burn the tracks onto a CD-R. As is the case for editing, the procedures for burning a CD vary depending on your software. Consult your manual or help files.
11. Pop the CD in the stereo and enjoy the music!

[edit] Tips

• It is probably easiest to use one software application to both record and edit, but you may also use two programs: a recording application and a WAV editor. Some highly recommended programs include GoldWave, Wave Repair, PolderbitS, and Audacity (free and open source with a lot of useful features). You can also search for "audio recorder" in a search engine and turn up a number of products, some free.
• If you don't need CDs and just want to convert your records to mp3s, you can save your finished recordings directly as mp3s (depending on your software) and skip the burning/ripping process. Same goes with any other format such as ogg vorbis.
• If you don't already have good recording equipment and software, and you just want to record a few LPs, you really might be better off just buying the CDs. You may be surprised how many old LPs are now available on CD. Unless you have a large vinyl collection or LPs that can't be found on CD, it might not be worth the time and expense to record your LPs yourself.
• You may be able to skip the computer and sound card altogether if you get a good CD-RW recorder. These can be connected directly to your stereo receiver so that you can record LPs onto CDs as easily as you used to record onto cassette tapes. If you want to edit the recording, you can simply use your CD to transfer the files to your computer and burn additional copies with your computer's CD burner.
• Get the right turntable. If you have a record collection, you've probably got a turntable. While you'll be able to make your recording using almost any turntable, the quality of your finished CD depends heavily on the quality of your equipment. The pawnshop-special record player in your basement may not be suitable for recording purposes.
• Get the right sound card. You don't need a professional-quality sound card to make a good recording, but the standard-issue cards that come with many computers just won't do, especially if they don't have a "line in" jack. (Jacks labeled "mic in" are usually mono and won't provide good quality for this purpose.) If you already have a sound card, try recording with it. It could be fine, or you might want to upgrade.
• If you used a freeware program, it will probably save in mp3 or WAV form, but if you use Microsoft Plus, it will save as a Windows Media file, which you can convert to mp4 using iTunes or burn directly to a CD with Windows Media Player. Because mp3 and Windows Media are lossy formats where some data is thrown out, save to AIFF or WAV with no compression; AIFF is the standard in MacOS, and WAV in Windows, but they are both cross-compatible and provide good quality when recorded at a high sample rate and bit depth, such at 44.1k samples per second, and 16 bits per sample. These uncompressed formats yield large files, but you can delete them once you've edited and burned them to CD.
• When editing, feel free to play around with your software's noise reduction and equalizer tools until you get a good sound. This will usually involve a bit of trial and error, so you should always make sure to save the original recording unaltered and then rename edited files. That way, if your editing actually worsens the sound quality you can always go back to the original and start again without having to re-record the LP.
• If you have a laptop, it may not be feasible to use a sound card. In this case, you can utilize a USB audio interface device. As will all the equipment, these vary in quality, so shop around and read reviews before buying.
• There are CD-Rs that have the look and feel of vinyl, which are relatively inexpensive.
• Some recording/editing software will allow you to change the speed of the recorded audio (the "Change Speed" effect in Audacity) so you can, say, record a 33-rpm record at 45 or even 78 rpm and then convert it back to the right speed, thus saving recording time. Depending on your equipment and settings, this can result in decreased quality, so generally this method should be saved for special circumstances such as if your turntable can't play at the right speed for a given record.

[edit] Warnings

• Turntables are extremely sensitive to vibration. Of course you can expect the LP to skip if you bump the table it's on, but other, less harsh vibrations can also affect your sound quality. While recording, try to minimize background noise–make the room as soundproof as possible and step lightly.
• Exercise the utmost care when cleaning an LP. LPs are actually quite resilient, but even the smallest scratch can produce popping or hissing noises, and once you've damaged the vinyl it can be difficult or impossible to repair. If you're not sure what you're doing, ask the staff of your local record store or do some research online.
• Do not hook up your computer sound card to a speaker output on your stereo receiver. The signal from a speaker output is likely cialis pills too powerful, and it could cause serious damage to the sound card.
• Power down either the computer and/or the audio source before the final connection. The intial surge can damage circuits with some combinations of sound card and audio source. Sound cards are especially sensitive to this damage.
• If hardware installation is needed, be sure to take the usual precautions: turn off power to the computer, "ground" yourself by touching something else metal before touching the inside of the computer case and make back-ups of any critical information stored on your computer (i.e. "the next great novel" that you've been writing) by either copying to a 3.5" floppy or e-mailing the file to a friend or relative.

[edit] Things You'll Need

• Cherished vinyl records
• Electric turntable (record player)
• PC with sound card or USB audio interface device with "line in"
• Cables and/or converters to connect PC to turntable or preamp
• Preamp or stereo receiver
• Audio recording and editing software
• At least 700 MB of free hard drive space
• CD burner
• Blank CD-R media

[edit] Related wikiHows

• How to Record a CD
• How to Burn a Music CD Using Windows Media Player 9
• How to Convert Protected Audio Into a Plain MP3
• How to Make a Perfect Mix Tape or CD
• How to Sell Old Phonograph Records
• How to Convert Vinyl to CD Using Golden Records

[edit] Sources and Citations

• Clive Barkham Thorough, but technical guide to recording LPs to CD]
• Blaze Audio Step-by-step tutorial to the recording process.]
• Guide to LP cleaning and care
• Stereophile Product reviews and information.
• HarddiskOgg a tool for recording vinyl (or other analog input) to your hard drive.
• Audacity a free and open source sound editor with many features useful for recording and editing vinyl records.